Wall Flange Kit 32mm MDPE + 19mm Barbed Geka Set
Wall Flange Kit 32mm MDPE + 19mm Barbed Geka Set is a ready-to-use connection package for MDPE piping projects, aimed at tradespeople installing water supply or irrigation lines. It combines a 32mm MDPE wall flange with two robust Geka fittings to simplify connecting MDPE to wall outlets and hose systems.
- 1 x MDPE Wall Flange 32mm – ¾” BSP (MDPEWF32-34BSPF)
- 1 x Geka Type Fitting ¾” BSP (GK34BSPM)
- 1 x Geka Type Fitting 19mm Barb (GK19MM)
MDPE fittings are designed for water supply, irrigation and light industrial use, offering durability, flexibility and chemical resistance. The wall flange enables a secure, neat entry point where MDPE pipe meets a flat surface, while the PN10 rating means the fittings are suitable for systems operating up to 10 bar (approximately 145 psi) under typical conditions. These fittings resist corrosion and weathering, helping reduce maintenance over the system’s life.
The kit’s Geka fittings use a claw (Geka) coupling design, known for quick, tool-free assembly and reliable seals. The brass construction affords good durability in harsh environments, and the rubber seals provide a watertight and airtight connection when fully engaged. The design permits rapid coupling and decoupling, helping minimise downtime on site while maintaining a secure, low-leak connection between pipes and hoses.
Typical applications include outdoor water supplies, irrigation runs, and brief-to-long-term fluid transfers where a 32mm MDPE run must connect to a ¾” BSP threaded interface or to a 19mm hose/barb system. The combination of MDPE compression/wall flange with Geka claw fittings offers a compact, versatile solution for joining MDPE piping to fixtures, valves or hoses without complex installation tools.
Installation considerations:
- Cut MDPE pipe square and deburr before inserting into compression ends or barb fittings.
- Ensure the wall flange seat is clean and the seal faces are free of debris before tightening.
- Hand-tighten BSP connections and finish with an approved sealant or PTFE where recommended for threaded portions; do not overtighten.
- Inspect all rubber seals for damage; replace if there is any wear to preserve a watertight, airtight seal.
Product Information
Product Information
Shipping & Returns
Shipping & Returns
Wall Flange Kit 32mm MDPE + 19mm Barbed Geka Set
Wall Flange Kit 32mm MDPE + 19mm Barbed Geka Set
Wall Flange Kit 32mm MDPE + 19mm Barbed Geka Set is a ready-to-use connection package for MDPE piping projects, aimed at tradespeople installing water supply or irrigation lines. It combines a 32mm MDPE wall flange with two robust Geka fittings to simplify connecting MDPE to wall outlets and hose systems.
- 1 x MDPE Wall Flange 32mm – ¾” BSP (MDPEWF32-34BSPF)
- 1 x Geka Type Fitting ¾” BSP (GK34BSPM)
- 1 x Geka Type Fitting 19mm Barb (GK19MM)
MDPE fittings are designed for water supply, irrigation and light industrial use, offering durability, flexibility and chemical resistance. The wall flange enables a secure, neat entry point where MDPE pipe meets a flat surface, while the PN10 rating means the fittings are suitable for systems operating up to 10 bar (approximately 145 psi) under typical conditions. These fittings resist corrosion and weathering, helping reduce maintenance over the system’s life.
The kit’s Geka fittings use a claw (Geka) coupling design, known for quick, tool-free assembly and reliable seals. The brass construction affords good durability in harsh environments, and the rubber seals provide a watertight and airtight connection when fully engaged. The design permits rapid coupling and decoupling, helping minimise downtime on site while maintaining a secure, low-leak connection between pipes and hoses.
Typical applications include outdoor water supplies, irrigation runs, and brief-to-long-term fluid transfers where a 32mm MDPE run must connect to a ¾” BSP threaded interface or to a 19mm hose/barb system. The combination of MDPE compression/wall flange with Geka claw fittings offers a compact, versatile solution for joining MDPE piping to fixtures, valves or hoses without complex installation tools.
Installation considerations:
- Cut MDPE pipe square and deburr before inserting into compression ends or barb fittings.
- Ensure the wall flange seat is clean and the seal faces are free of debris before tightening.
- Hand-tighten BSP connections and finish with an approved sealant or PTFE where recommended for threaded portions; do not overtighten.
- Inspect all rubber seals for damage; replace if there is any wear to preserve a watertight, airtight seal.
Original: $20.01
-65%$20.01
$7.00Product Information
Product Information
Shipping & Returns
Shipping & Returns
Description
Wall Flange Kit 32mm MDPE + 19mm Barbed Geka Set is a ready-to-use connection package for MDPE piping projects, aimed at tradespeople installing water supply or irrigation lines. It combines a 32mm MDPE wall flange with two robust Geka fittings to simplify connecting MDPE to wall outlets and hose systems.
- 1 x MDPE Wall Flange 32mm – ¾” BSP (MDPEWF32-34BSPF)
- 1 x Geka Type Fitting ¾” BSP (GK34BSPM)
- 1 x Geka Type Fitting 19mm Barb (GK19MM)
MDPE fittings are designed for water supply, irrigation and light industrial use, offering durability, flexibility and chemical resistance. The wall flange enables a secure, neat entry point where MDPE pipe meets a flat surface, while the PN10 rating means the fittings are suitable for systems operating up to 10 bar (approximately 145 psi) under typical conditions. These fittings resist corrosion and weathering, helping reduce maintenance over the system’s life.
The kit’s Geka fittings use a claw (Geka) coupling design, known for quick, tool-free assembly and reliable seals. The brass construction affords good durability in harsh environments, and the rubber seals provide a watertight and airtight connection when fully engaged. The design permits rapid coupling and decoupling, helping minimise downtime on site while maintaining a secure, low-leak connection between pipes and hoses.
Typical applications include outdoor water supplies, irrigation runs, and brief-to-long-term fluid transfers where a 32mm MDPE run must connect to a ¾” BSP threaded interface or to a 19mm hose/barb system. The combination of MDPE compression/wall flange with Geka claw fittings offers a compact, versatile solution for joining MDPE piping to fixtures, valves or hoses without complex installation tools.
Installation considerations:
- Cut MDPE pipe square and deburr before inserting into compression ends or barb fittings.
- Ensure the wall flange seat is clean and the seal faces are free of debris before tightening.
- Hand-tighten BSP connections and finish with an approved sealant or PTFE where recommended for threaded portions; do not overtighten.
- Inspect all rubber seals for damage; replace if there is any wear to preserve a watertight, airtight seal.
